silivriserdar
Genel Moderator
- Katılım
- 21 Haz 2018
- Mesajlar
- 21,966
- Tepkime puanı
- 44,591
- Puanları
- 113
- Yaş
- 40
Çevrimdışı
Merhaba gsmturkey.net üyeleri bu paylaşacağım konuda Casper VIA S17 cihazının yazılımı NCK Dongle ile nasıl çekilir onu anlatacağım.
Bu işlemi yapabilmek için elinizde NCK Dongle olması lazım. Bu araç ücretli bir araçtır ve genellikle cep telefonu tamir yapan yerlerde mevcuttur.
NCK Dongle Android MTK Tool'u açın ve Backup kısmından Dump Firmware basın.
Cihazı kapatın 10 saniye bekleyin ardından power tuşunun yanında olan küçük reset tuşuna iğne yardımı ile basın. Ve o şekilde sağlam bir usb kablo ile pc'ye bağlayın. İğneyi çekin ve yazılım yüklemesi başlayacaktır.
Kod:
Action : Read Firmware.
Selected 0-By CPU:ELBRUS
Exe version: NCKDongle AndroidMTK 2.5.9.8
Will be used loader: DA_PL.bin
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : MediaTek PreLoader USB VCOM (Android) (COM4)
Boot mode: Preloader
BBCHIP: 8163 0 ca00
Using Algo 1.
Phone detected...Please wait
Sending DA agent, please wait...
----------------------------------------------------
BaseBand CPU :MT8163
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 01
----------------------------------------------------
INT RAM: 256 KB SDRAM
EXT RAM: 1 GB DRAM
----------------------------------------------------
EMMC: (117Gb+8192Mb) SANDISK 0x444634303136
EMMC FW VERSION: 01:00:00:00:00:00:00:00
EMMC CID: 450100444634303136 : 00000000000000
EMMC UA SIZE: 0x3ab400000
BOOT STYLE: EMMC BOOT
FULL LENGTH: 0x3ac000000 [14.688 GB]
Status: USB_HIGH_SPEED
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detected : MediaTek DA USB VCOM (Android) (COM5)
Build ID: MRA58K
Display ID: VIA_S17_20170426_c1.01
Version: 6.0
Model: VIA_S17
Brand: Casper
Device: VIA_S17
Manufacturer: Casper
Mediatek Version Release: alps-mp-m0.mp8-V1.0.1_pskyed8163.tb.e.m_P3
Dumping Preloader.
Start dumping flash, this can take up to 1 hour.......
Start processing proinfo
Reading: BEGIN: 0x80000 - LEN: 0x300000
Start processing nvram
Start processing protect1 ......
Reading: BEGIN: 0x880000 - LEN: 0xa00000
Start processing protect2 ......
Reading: BEGIN: 0x1280000 - LEN: 0xa00000
Start processing lk ......
Start processing boot
Start processing recovery
Start processing secro
Reading: BEGIN: 0x3d20000 - LEN: 0x600000
[6013]ReadbackPartitionToBuffer fail!: To download SEC_RO is forbidden in this phone.
Start processing logo ......
Start processing frp ......
Reading: BEGIN: 0x55a0000 - LEN: 0x100000
Start processing trustzone
Start processing system
Reading: BEGIN: 0x8800000 - LEN: 0xc0000000
Saved to : C:\Users\Serdar\Documents\Android_MTK\firmware_backup\MT8163_EMMC_Casper_VIA_S17_6_0_alps-mp-m0_mp8-V1_0_1_pskyed8163_tb_e_m_P3(2019_03_28_15_16)
Wait untill phone will start charging.
[0]All done.