silivriserdar
Genel Moderator
- Katılım
- 21 Haz 2018
- Mesajlar
- 21,975
- Tepkime puanı
- 44,630
- Puanları
- 113
- Yaş
- 40
Çevrimdışı
Merhaba GSM Turkey üyeleri bu paylaşacağım konuda Meizu M3 Note L681H Cihazına ait CM2 Dongle ile nasıl read firmware yapılır onu anlatacağım.
Bu işlemi yapabilimek için elinizde CM2 Dongle olması lazım. Bu araç ücretli bir araçtır ve genellikle cep telefonu tamir yapan yerlerde mevcuttur.
Bu işlemi yapabilimek için elinizde CM2 Dongle olması lazım. Bu araç ücretli bir araçtır ve genellikle cep telefonu tamir yapan yerlerde mevcuttur.
Kod:
1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...
PTFN : MediaTek USB Port (COM5)
MODE : BOOTROM
PORT : 5
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6755 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0001
TYPE : MODERN RAPHAEL
BROM : MEID : E71D8C107EF9B9B8F5A1298FD45C9B07
BROM : SecLevel : 0x00000007
BROM : SecMode : SBC+SLA+SDA
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : 0_base : BASE_v2112 | Manual : Disabled
BROM : SLA : Local Auth
BROM : SLA : Auth Started!
BROM : SLA : Auth Passed!
BROM : SLA : 0x000000FE
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6755
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : MT6755
EMI : SRC : preloader_hq6755_66_b1a_l.bin
EMI : CNT : 0006
EMI : [00] : eMMC : DDR3 : ID : 90014A484147326505 : VEN : HYNIX | DEV : HAG2e : RAM : [ 2,00 GB ]
EMI : [01] : eMMC : DDR3 : ID : 150100514531334D42 : VEN : SAMSUNG | DEV : QE13MB : RAM : [ 2,00 GB ]
EMI : [02] : eMMC : DDR3 : ID : 90014A484247346132 : VEN : HYNIX | DEV : HBG4a2 : RAM : [ 3,00 GB ]
EMI : [03] : eMMC : DDR3 : ID : 150100525831424D42 : VEN : SAMSUNG | DEV : RX1BMB : RAM : [ 3,00 GB ]
EMI : [04] : eMMC : DDR3 : ID : 90014A484147346132 : VEN : HYNIX | DEV : HAG4a2 : RAM : [ 2,00 GB ]
EMI : [05] : eMMC : DDR3 : ID : 13014E51334A393756 : VEN : MICRON | DEV : Q3J97V : RAM : [ 3,00 GB ]
EMI : Init EMI from PRELOADER
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info
SRAM: 0x00038000 [ 224,00 KB ]
DRAM: 0x80000000 [ 2,00 GB ]
EMMC: 90014A484147346132A40D79BCECA399
EMMC: VEN : HYNIX | OEM : 4A01 | DEV : HAG4a2
EMMC:
BOOT1 : 0x00400000 [ 4,00 MB ]
BOOT2 : 0x00400000 [ 4,00 MB ]
RPMB : 0x00400000 [ 4,00 MB ]
USER : 0x3AB400000 [ 14,68 GB ]
CHIP : MT6755 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0000 , EVOL : 0x0000
RNID : 6B5197981C0AD0D36622189B4B823B55
DA : USB : FULL-SPEED
DA : USB : Change Port Speed
PTFN : MediaTek DA USB VCOM (Android) (COM14)
MODE : PRELOADER PORT
PORT : 14
Boot done!
Patch Level : LMY47I
Ver. CodeName : REL
Ver. Release : 5.1
Sec. Patch : 2018-03-05
Build Time : 11.04.2018
Board Platform : mt6755
Product Brand : Meizu
Product Manfct : Meizu
Display ID : Flyme 6.3.0.0G
Product Model : m3 note
Product Name : m3note
Product Device : m3note
Product Board : m3note
Product Info : m3note
MT6755_Meizum3_note5.1Flyme_6.3.0.0GLMY47I_m3note
Read : preloader.bin
Read : recovery.img
Read : custom.img
ExtSparse : Compression ratio : 83%
Read : proinfo.img
Read : md1rom.img
Read : md1dsp.img
Read : md1arm7.img
Read : md3rom.img
Read : nvram.bin
Read : lk.bin
Read : boot.img
Read : logo.bin
Read : tz.img
Read : secro.img
Read : devinfo.img
Read : system.img
ExtSparse : Compression ratio : 49%
Read : cache.img
Read : userdata.img
FW Size : 1,49 GB
Android Info saved : _Android_info.txt
Scatter : MT6755_Android_scatter.txt
Saved to : C:\Users\comma\Desktop\L681H\MT6755_Meizum3_note5.1Flyme_6.3.0.0GLMY47I_m3note\
Done!
Elapsed: 00:03:38