Çözüldü Xiaomi 11T Agate Null ve Patch Ok

[King]

Ben bu işlemi pandora ile yaptım fakat siz chimera ile de yapabılırsınız yada elinizde sihirli nvram nvdata dosyanız da var ise olabilir.

The King İs Back
Selected model: Xiaomi 21081111RG (11T)
Operation: Patch CERT
Software version: 3.8

Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0950
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6893]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM394 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0950
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6893]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xB9DAAE2F, 0x1977E49D, 0x3363B271, 0xFEC6863F
Get Chip ID... [MT6893]
Get SOC ID... [274874CE62E1F4541ECC0D776F2E158379B6AE920DA6C8539AF096DC4FFB29DE]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [19]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KLUEG8UHDC-B0E1 (0200)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KLUEG8UHDC-B0E1
UFS_FWVER : 0200
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x3B96000000 (238.34Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK [A]
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Load partiton for patching... OK
Check boot patch possiblity... POSSIBLE WITH BOOT UNLOCK
Patching CERT... OK
Save patched partiton... OK
Format "parameter" partition... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.

 

[Kerem47]

Ben bu işlemi pandora ile yaptım fakat siz chimera ile de yapabılırsınız yada elinizde sihirli nvram nvdata dosyanız da var ise olabilir.

The King İs Back
Selected model: Xiaomi 21081111RG (11T)
Operation: Patch CERT
Software version: 3.8

Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0950
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6893]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM394 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0950
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6893]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xB9DAAE2F, 0x1977E49D, 0x3363B271, 0xFEC6863F
Get Chip ID... [MT6893]
Get SOC ID... [274874CE62E1F4541ECC0D776F2E158379B6AE920DA6C8539AF096DC4FFB29DE]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [19]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KLUEG8UHDC-B0E1 (0200)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KLUEG8UHDC-B0E1
UFS_FWVER : 0200
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x3B96000000 (238.34Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK [A]
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Load partiton for patching... OK
Check boot patch possiblity... POSSIBLE WITH BOOT UNLOCK
Patching CERT... OK
Save patched partiton... OK
Format "parameter" partition... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.

Ekli dosyayı görüntüle 18398

Ekli dosyayı görüntüle 18399

Chimera ile deneme yaptım imeiler geliyor ama cert olmuyor nvdata'ya düşüyor.GsmTurkey özel metodla 10 dk içinde %100 başarılı oluyor.Boxlara gerek bile kalmıyor.

 

[silivriserdar]

Çözüldü - Xiaomi 5G Dimensity İşlemcili Cihazlarda NV Silinmesi Çözülmüştür​

 

[nrllh038]

Ben bu işlemi pandora ile yaptım fakat siz chimera ile de yapabılırsınız yada elinizde sihirli nvram nvdata dosyanız da var ise olabilir.

The King İs Back
Selected model: Xiaomi 21081111RG (11T)
Operation: Patch CERT
Software version: 3.8

Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0950
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6893]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM394 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0950
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6893]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xB9DAAE2F, 0x1977E49D, 0x3363B271, 0xFEC6863F
Get Chip ID... [MT6893]
Get SOC ID... [274874CE62E1F4541ECC0D776F2E158379B6AE920DA6C8539AF096DC4FFB29DE]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [19]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KLUEG8UHDC-B0E1 (0200)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KLUEG8UHDC-B0E1
UFS_FWVER : 0200
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x3B96000000 (238.34Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK [A]
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Load partiton for patching... OK
Check boot patch possiblity... POSSIBLE WITH BOOT UNLOCK
Patching CERT... OK
Save patched partiton... OK
Format "parameter" partition... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.

Ekli dosyayı görüntüle 18398

Ekli dosyayı görüntüle 18399

Eline sağlık USTA sen paylaşana kadar kimseden ses yoktu

 

[ysfzyemr]

Eline sağlık USTA sen paylaşana kadar kimseden ses yoktu

Aşağıdaki açılan konuya bir göz atın isterseniz sayın @Negative ustamız bu olayı çoktan çözmüş ve ilklerin yeri olan GSM TURKEY ailesi olarak konu herkese duyurulmuştur.

Çözüldü - Xiaomi MTK 4G 5G Dimensity İşlemcili Cihazlarda NV Silinmesi Null ve Şebeke Sorunu %100 Çözülmüştür

Merhaba değerli GSM Turkey üyeleri. Forumdan uzak kaldığımız için V.I.P Telegram grubumuzda bu konuyu yayınlamıştık. Ancak bazı "kişiler" bizlere kafa tutmaya çalışınca genel olarak paylaşım yapmaya karar verdik. Orjinal NV Yedeği kaybolmuş yeni nesil cihazlar, sıfırlama sonucu ve yazılım...

gsmturkey.net

​

 

[azik436]

Arkadaşlar lütfen bana yardımcı ola bilirmisiniz? Bana Mi 11T nin Nvram dosyası lazım. Orijinal yedeği almadım. Rica ederim bana yardım edin. Şimdiden teşekkürler

 

[odunbey]

Arkadaşlar lütfen bana yardımcı ola bilirmisiniz? Bana Mi 11T nin Nvram dosyası lazım. Orijinal yedeği almadım. Rica ederim bana yardım edin. Şimdiden teşekkürler

başka bir cihaza ait nvram dosyasını atsanızda yıne açmayacaktır profesyonel araçlar ile düzeltilebilir
whatsapp hattımızdan bizimle iletişime geçebilirsiniz