Xiaomi Poco M3 Pro 5G M2103K19PG IMEI Repair İşlemi

Ü

ÜlviExador

Üye
Katılım
3 Ağu 2019
Mesajlar
111
Tepkime puanı
36
Puanları
28
Çevrimdışı
merhaba bu model telefona Z3X Pandora boxla repair yaptım her şey sorunsuz geçiyor ama telefon açılmıyor bilgisi olan varsa yardım gerekli .


Selected model: Xiaomi M2103K19PG (Poco M3 Pro 5G)
Operation: Repair
Software version: 3.4

Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM47 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xB0D9520E, 0x8470AF9E, 0x48AB02AE, 0x1ACEEAD5
Get Chip ID... [MT6833]
Get SOC ID... [2D321EC680374962BDCE42088BDF66AA0AE3AD8FB244E411E35A0B5D612457A1]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): H9HQ15AECMBDAR (A043)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : H9HQ15AECMBDAR
UFS_FWVER : A043
BLOCK_SIZE: 0x0000001000 (4,00Kb)
UFS_LU0 : 0x0000400000 (4,00Mb)
UFS_LU1 : 0x0000400000 (4,00Mb)
UFS_LU2 : 0x1DCB000000 (119,17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448,00Kb)
EXT_RAM : 0x0100000000 (4,00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK [A]
Read product info... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : M2103K19C
Product Name : camellia
Product Device : camellia
Product Board : camellia
Board Platform : MT6833
Build ID : RP1A.200720.011
Build Date : Fri Jun 25 14:56:54 CST 2021
Display ID : AN3516-camellia-build-2021062514
Security Patch : 2020-12-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 3516
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read IMEI... OK
IMEI 1: xxxxxxxxxxx
IMEI 2: xxxxxxxxxxx
Repairing IMEI...
IMEI 1: xxxxxxxxxxxxxxx
IMEI 2: xxxxxxxxxxxxxxx
Write IMEI [NVDATA]... OK
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!


ve patch işlemi

Selected model: Xiaomi M2103K19PG (Poco M3 Pro 5G)
Operation: Patch CERT
Software version: 3.4

Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM47 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xB0D9520E, 0x8470AF9E, 0x48AB02AE, 0x1ACEEAD5
Get Chip ID... [MT6833]
Get SOC ID... [2D321EC680374962BDCE42088BDF66AA0AE3AD8FB244E411E35A0B5D612457A1]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): H9HQ15AECMBDAR (A043)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : H9HQ15AECMBDAR
UFS_FWVER : A043
BLOCK_SIZE: 0x0000001000 (4,00Kb)
UFS_LU0 : 0x0000400000 (4,00Mb)
UFS_LU1 : 0x0000400000 (4,00Mb)
UFS_LU2 : 0x1DCB000000 (119,17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448,00Kb)
EXT_RAM : 0x0100000000 (4,00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK [A]
Read product info... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : M2103K19C
Product Name : camellia
Product Device : camellia
Product Board : camellia
Board Platform : MT6833
Build ID : RP1A.200720.011
Build Date : Fri Jun 25 14:56:54 CST 2021
Display ID : AN3516-camellia-build-2021062514
Security Patch : 2020-12-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 3516
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Patch CERT [NVDATA]... OK
Patch CERT [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.
 
xwhoamix00' Alıntı:
EDL Modda Yazılım Yüklemeyi Dene.​
Genişletmek için tıkla ...
mtk işlemci EDL olmaz bunlarda
Mesaj Otomatik Birleştirildi:

sorun telefonun açılmaması değil nv data erase yapınca açılıyor sorun pandora boxla çift repair yapılınca açılmaması
 
Pardon Şaşırmışım :) "Maui Meta" Üzerinden DB`i Çek Ve Yeniden Sp Flash Tool Üzerinden Yazılım Yükle. Bunları Dene
Bide Maui Meta Üzerinden Repair Yap Şansını Dene.​
 
xwhoamix00' Alıntı:
Pardon Şaşırmışım :) "Maui Meta" Üzerinden DB`i Çek Ve Yeniden Sp Flash Tool Üzerinden Yazılım Yükle. Bunları Dene
Bide Maui Meta Üzerinden Repair Yap Şansını Dene.​
Genişletmek için tıkla ...
sorun telefonun açılmaması değil, çalışıyor sadece imei repair yapınca sorun çıkıyor ama Pandorayla yapıldığı için olmaması laızm böyle bir sorun
 
ÜlviExador' Alıntı:
merhaba bu model telefona Z3X Pandora boxla repair yaptım her şey sorunsuz geçiyor ama telefon açılmıyor bilgisi olan varsa yardım gerekli .


Selected model: Xiaomi M2103K19PG (Poco M3 Pro 5G)
Operation: Repair
Software version: 3.4

Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM47 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xB0D9520E, 0x8470AF9E, 0x48AB02AE, 0x1ACEEAD5
Get Chip ID... [MT6833]
Get SOC ID... [2D321EC680374962BDCE42088BDF66AA0AE3AD8FB244E411E35A0B5D612457A1]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): H9HQ15AECMBDAR (A043)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : H9HQ15AECMBDAR
UFS_FWVER : A043
BLOCK_SIZE: 0x0000001000 (4,00Kb)
UFS_LU0 : 0x0000400000 (4,00Mb)
UFS_LU1 : 0x0000400000 (4,00Mb)
UFS_LU2 : 0x1DCB000000 (119,17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448,00Kb)
EXT_RAM : 0x0100000000 (4,00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK [A]
Read product info... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : M2103K19C
Product Name : camellia
Product Device : camellia
Product Board : camellia
Board Platform : MT6833
Build ID : RP1A.200720.011
Build Date : Fri Jun 25 14:56:54 CST 2021
Display ID : AN3516-camellia-build-2021062514
Security Patch : 2020-12-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 3516
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read IMEI... OK
IMEI 1: xxxxxxxxxxx
IMEI 2: xxxxxxxxxxx
Repairing IMEI...
IMEI 1: xxxxxxxxxxxxxxx
IMEI 2: xxxxxxxxxxxxxxx
Write IMEI [NVDATA]... OK
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!


ve patch işlemi

Selected model: Xiaomi M2103K19PG (Poco M3 Pro 5G)
Operation: Patch CERT
Software version: 3.4

Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM47 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xB0D9520E, 0x8470AF9E, 0x48AB02AE, 0x1ACEEAD5
Get Chip ID... [MT6833]
Get SOC ID... [2D321EC680374962BDCE42088BDF66AA0AE3AD8FB244E411E35A0B5D612457A1]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): H9HQ15AECMBDAR (A043)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : H9HQ15AECMBDAR
UFS_FWVER : A043
BLOCK_SIZE: 0x0000001000 (4,00Kb)
UFS_LU0 : 0x0000400000 (4,00Mb)
UFS_LU1 : 0x0000400000 (4,00Mb)
UFS_LU2 : 0x1DCB000000 (119,17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448,00Kb)
EXT_RAM : 0x0100000000 (4,00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK [A]
Read product info... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : M2103K19C
Product Name : camellia
Product Device : camellia
Product Board : camellia
Board Platform : MT6833
Build ID : RP1A.200720.011
Build Date : Fri Jun 25 14:56:54 CST 2021
Display ID : AN3516-camellia-build-2021062514
Security Patch : 2020-12-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 3516
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Patch CERT [NVDATA]... OK
Patch CERT [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.
Genişletmek için tıkla ...
Bu modele ait en düşük yazılım sürümü yazılım ile deneyin. Bootloader kilidi original mi hesabı ile açılmış olarak deneyin. Root ve rootsuz şekilde deneyin. Hiç biri olmaz ise büyük bir ihtimalle test etmeden eklenmiştir. Şu an çoğu Xioami modeli test aşamasında yeni yeni yapılmaya başlandı.

Tüm videolar: https://www.youtube.com/playlist?list=PLy3DUl4-MY1OvomBk9s5_XrY09eDLkdi1​
 
silivriserdar' Alıntı:
Bu modele ait en düşük yazılım sürümü yazılım ile deneyin. Bootloader kilidi original mi hesabı ile açılmış olarak deneyin. Root ve rootsuz şekilde deneyin. Hiç biri olmaz ise büyük bir ihtimalle test etmeden eklenmiştir. Şu an çoğu Xioami modeli test aşamasında yeni yeni yapılmaya başlandı.



Tüm videolar: https://www.youtube.com/playlist?list=PLy3DUl4-MY1OvomBk9s5_XrY09eDLkdi1​
Genişletmek için tıkla ...

root dışında bir çok şekilde denedim sorunu buldum tamamen pandorayla alakalı boot patch ederken hata yapıyor , mesela redmi 9a sekmesinden 9a ya yapmıyor ama redmi 9 a girip 9a yapılabiliyor herhalde güncellemeyle yavaş-yavaş ortadan kalkar çok teşekkür ederim bilgi için
 
Cevap yazmak için giriş yap yada kayıt ol.
Geri
Üst Alt