Çözüldü ZTE Axon 7 Mini B2017G IMEI Repair Sorunu

cek10' Alıntı:
Operation : Repair IMEI
Searching for Device in FTM Mode...Found
Port : ZTE Handset Diagnostic Interface (COM8)
Hardware ID : usb\vid_19d2&pid_0500&rev_0310&mi_00
Compile : May 18 2017 22:21:07
Release : Mar 06 2017 23:00:00
Hw. Ver. : 8952.gen
Software : P852A11V1.2.0B09_MR
IMEI : 860567030360736 / 860567030360744
Reading QCN Data...Done
Saved As : C:\UMTool\QcFire\QCN_Backup\8952.gen_P852A11V1.2.0B09_MR_860567030360736_190304_133412.qcn
Switching to EDL Mode...Done
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Android HS-USB QDLoader 9008 (COM4)
Driver Info : TCL, qcusbser.sys, 2.1.2.1
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1209700 [8952] 04000000
OPK_DATA : E8905D68B0F309D55B9E28678BFCB56A2447AF1F730EC152AEBEF94F0DB377C8
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8952_006]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8952, eMMC, 32 GB
LU Count : 1 [0x03A3E000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 16384, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : ZTE ZTE B2017G [msm8952]
Software : ZTE B2017GV1.2.0B09, 20170519.163520 [Fri May 19 16:35:15 CST 2017]
Android Ver. : 7.1.1
Patch Level : 2017-06-01
Saving EFS Backup.......OK
EFS Backup : EFS_ZTE_ZTE B2017G_ZTE B2017GV1.2.0B09_2017-06-01_190304_133600.ueb
Reset EFS (Full)......Done
Processing background tasks...Done
Restoring QCN Data...Done
Finalizing process...Done
Operation Finished.
QcFire Ver. 3.8
FTM modda yapdi amma sebeke yine yok
Genişletmek için tıkla ...
Qcn dosya verebilir misin bana Sana zahmet
 
ustalar sorun davam ediyor bende olan telefonda surum 6.0.1 Sigma box repair islemin yapdim FTP modunda qayet basarli amma siqnal yok gelmiyo sorun ne ola bilir UMT box efs sifirladimda yine olmadi yardimci olursaniz sevinirim
 
samirbagisov' Alıntı:
ustalar sorun davam ediyor bende olan telefonda surum 6.0.1 Sigma box repair islemin yapdim FTP modunda qayet basarli amma siqnal yok gelmiyo sorun ne ola bilir UMT box efs sifirladimda yine olmadi yardimci olursaniz sevinirim
Genişletmek için tıkla ...
Şebeke barın olduğu yeri foto atarmısınız
 

Ekli dosyalar

  • 8721.jpeg
    8721.jpeg
    139.3 KB · Görüntüleme: 38
cek10' Alıntı:
Operation : Repair IMEI
Searching for Device in FTM Mode...Found
Port : ZTE Handset Diagnostic Interface (COM8)
Hardware ID : usb\vid_19d2&pid_0500&rev_0310&mi_00
Compile : May 18 2017 22:21:07
Release : Mar 06 2017 23:00:00
Hw. Ver. : 8952.gen
Software : P852A11V1.2.0B09_MR
IMEI : 860567030360736 / 860567030360744
Reading QCN Data...Done
Saved As : C:\UMTool\QcFire\QCN_Backup\8952.gen_P852A11V1.2.0B09_MR_860567030360736_190304_133412.qcn
Switching to EDL Mode...Done
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Android HS-USB QDLoader 9008 (COM4)
Driver Info : TCL, qcusbser.sys, 2.1.2.1
Connecting to phone...OK
Waiting for response ... OK
Init Handshake Sequence ... OK
Hardware ID: E1209700 [8952] 04000000
OPK_DATA: E8905D68B0F309D55B9E28678BFCB56A2447AF1F730EC152AEBEF94F0DB377C8
Initializing Protocol ... OK
Using Auto Loader Selection [1]
Preparing Loader ... Done
Sending Loader [8952_006] ... Done
Executing Loader ... OK
Detecting Chip Type ... OK
Hardware: 8952, eMMC, 32 GB
LU Count: 1 [0x03A3E000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire \ Drivers folder using Device Manager.
Payload Info: In: 65536 [4096], Out: 16384, Sector Size: 512
Reading Partition Table ... OK
Reading Device Information ... OK
Device: ZTE ZTE B2017G [msm8952]
Software: ZTE B2017GV1.2.0B09, 20170519.163520 [Fri May 19 16:35:15 CST 2017]
Ver Android. : 7.1.1
Patch Level: 2017-06-01
Saving EFS Backup ....... OK
EFS Backup: EFS_ZTE_ZTE B2017G_ZTE B2017GV1.2.0B09_2017-06-01_190304_133600.ueb
Reset EFS (Full) ...... Done
Processing background tasks ... Done
Restoring QCN Data ... Done
Finalizing process ... Done
Operation Finished.
QcFire Ver. 3.8
I did it in FTM mode but there is no network [/ QUOTE]
Genişletmek için tıkla ...
Mesaj Otomatik Birleştirildi:

[QUOTE = "cek10, post: 45215, member: 5826"] Operation: Repair IMEI
Searching for Device in FTM Mode ... Found
Port: ZTE Handset Diagnostic Interface (COM8)
Hardware ID: usb \ vid_19d2 & pid_0500 & rev_0310 & mi_00
Compile: May 18 2017 22:21:07
Release: Mar 06 2017 23:00:00
Hwa. Give. : 8952.gen
Software: P852A11V1.2.0B09_MR
IMEI: 860567030360736/860567030360744
Reading QCN Data ... Done
Saved As: C: \ UMTool \ QcFire \ QCN_Backup \ 8952.gen_P852A11V1.2.0B09_MR_860567030360736_190304_133412.qcn
Switching to EDL Mode ... Done
Checking for existing devices ... Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port: Android HS-USB QDLoader 9008 (COM4)
Driver Info: TCL, qcusbser.sys, 2.1.2.1
Connecting to phone ... OK
Waiting for response ... OK
Init Handshake Sequence ... OK
Hardware ID: E1209700 [8952] 04000000
OPK_DATA: E8905D68B0F309D55B9E28678BFCB56A2447AF1F730EC152AEBEF94F0DB377C8
Initializing Protocol ... OK
Using Auto Loader Selection [1]
Preparing Loader ... Done
Sending Loader [8952_006] ... Done
Executing Loader ... OK
Detecting Chip Type ... OK
Hardware: 8952, eMMC, 32 GB
LU Count: 1 [0x03A3E000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire \ Drivers folder using Device Manager.
Payload Info: In: 65536 [4096], Out: 16384, Sector Size: 512
Reading Partition Table ... OK
Reading Device Information ... OK
Device: ZTE ZTE B2017G [msm8952]
Software: ZTE B2017GV1.2.0B09, 20170519.163520 [Fri May 19 16:35:15 CST 2017]
Ver Android. : 7.1.1
Patch Level: 2017-06-01
Saving EFS Backup ....... OK
EFS Backup: EFS_ZTE_ZTE B2017G_ZTE B2017GV1.2.0B09_2017-06-01_190304_133600.ueb
Reset EFS (Full) ...... Done
Processing background tasks ... Done
Restoring QCN Data ... Done
Finalizing process ... Done
Operation Finished.
QcFire Ver. 3.8
I did it but there is no network in FTM mode [/ Q










can u share qcn file please
 
Selamün aleyküm digerli ustalar benim elimdede ZTE B2017G cihaz var şuan repair yapilmasi lazim sira ile anlatacak bir ustamiz varmi
 
b2017g repair yaparken qcn yedeği almadan işlem yaptım meid sıkıntısından dolayı cihaz uçak modundan çıkmıyor
qcn yedeğini paylaşabilirmisiniz..
 
merhaba zte b2017g icin edl modda firmware linki vere bilirmisiniz
 
Cevap yazmak için giriş yap yada kayıt ol.
Geri
Üst Alt