- Katılım
- 21 Haz 2018
- Mesajlar
- 11,495
- Tepkime puanı
- 28,082
- Puanları
- 113
Çevrimdışı
Merhaba arkadaşlar. bu konumuzda sizlere Exceed EX7W1 Plus Reset FRP işlemi nasıl yapılır onu anlatacağım.
Bu işlemi yapabilmek için elinizde CM2 tool olması gerekiyor. Bu araç ücretlidir ve teknik servislerde bulunur.
Dilerseniz yukarıda bulunan Whatsapp ve Telegram hesabımızdan da bizlerle iletişime geçip yaptırabilirsiniz.
Card found : 4B1E57BB , v0156
Infinity-Box Chinese Miracle II : SPD/USC Module [SP2] v2.14
Load IDBase v8331 Ok!
Operation : Identify [ v2.14 ]
BootMode : FLASH
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC7731E_BASE : SC7731E_eMMC_1GB_0S
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : 0x0008
FDL : EMMC_RO : False ; EMMC_PART : True ; EMMC_RPMB_SET : True
FDL : RAW : 0x0002
FDL : FLH : 0x400000
FDL : Control transfered!
Boot Done!
Device info :
Product Brand : EXCEED
Product Device : EX7W1S
Product Model : EX7W1 Plus
Product Name : EX7W1S
Patch Level : QP1A.190711.020
Display ID : EXCEED_EX7W1S_20220121
Ver. Incmt : 31318
Ver. CodeName : REL
Ver. Release : 10
Sec. Patch : 2020-08-05
Build Time : 21.01.2022
Product Info : EX7W1S
Product Board : sp7731e_1h10
Board Platform : sp7731e
Product Manfct : incar
Platform Version: MOCORTM_17C_W20.08.3_Debug
Project Version: pike2_pub
BASE Version: FM_BASE_17C_W20.08.3
HW Version: sc7731e_modem
CMP_Time : 02-19-2020 01:10:56
MODEM TAG : MOCORTM_17C_W20.08.3_Debug_FM_BASE_17C_W20.08.3_sc7731e_modem_pike2_pub
USERDATA : FILESYSTEM : F2FS with FDE ( Full Disk Encryption ***)
- > INFO : Remove cable from device to switch it off!
Done!
Elapsed: 00:00:53
Operation : Format FS / Reset Settings [ v2.14 ]
Mode : Reset FRP
BootMode : FLASH
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
>>> Device not found!
>>> Remove battery, cable. Check cable and connection. Repeat operation!
Reconnect Power/Cable!
Operation : Format FS / Reset Settings [ v2.14 ]
Mode : Reset FRP
BootMode : FLASH
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
>>> ERROR : Protocol HandShake failed!
>>> Error : Fail to init protocol!
>>> Remove battery, cable. Check cable and connection. Repeat operation!
Reconnect Power/Cable!
Operation : Format FS / Reset Settings [ v2.14 ]
Mode : Reset FRP
BootMode : FLASH
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC7731E_BASE : SC7731E_eMMC_1GB_0S
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : 0x0008
FDL : EMMC_RO : False ; EMMC_PART : True ; EMMC_RPMB_SET : True
FDL : RAW : 0x0002
FDL : FLH : 0x400000
FDL : Control transfered!
Boot Done!
Wipe Ok : FRP
Reconnect Power/Cable!
Done!
Elapsed: 00:00:21