silivriserdar
Genel Moderator
- Katılım
- 21 Haz 2018
- Mesajlar
- 21,994
- Tepkime puanı
- 44,702
- Puanları
- 113
- Yaş
- 40
Çevrimdışı
Merhaba GSM Turkey Üyeleri bu paylaşacağım konuda Huawei Honor 10X Lite DNN-LX9 cihazına ait FRP Reset ve Huawei ID Remove başarı raporunu paylaşacağım.
Ben bu işlemi Octoplus Box Huawei Tool ile yaptım. Bu araç ücretli bir araçtır.
BU CİHAZ UZAKTAN BAĞLANTI İLE YAPILABİLMEKTEDİR
İLETİŞİM İÇİN WHATSAP HATTIMIZİÇİN TIKLAYIN.
İLETİŞİM İÇİN TELEGRAM ADRESİMİZ TIKLAYIN.
Ben bu işlemi Octoplus Box Huawei Tool ile yaptım. Bu araç ücretli bir araçtır.
BU CİHAZ UZAKTAN BAĞLANTI İLE YAPILABİLMEKTEDİR
İLETİŞİM İÇİN WHATSAP HATTIMIZİÇİN TIKLAYIN.
İLETİŞİM İÇİN TELEGRAM ADRESİMİZ TIKLAYIN.
Kod:
Welcome to Octoplus Huawei Software v. 1.3.4
To enable 'Manufacture' mode dial
- for Qualcomm and Hisilicon based models: *#*#2846579#*#*
ProjectMenu > Background Settings > USB Port Settings > Manufacture Mode
- for MTK based models: *#*#14789632#*#*
ProjectMenu > Background Settings > USB Port Settings > Debug Mode
To enable 'Fastboot' mode
1. Power off the phone. Remove SD and SIM cards
2. Press 'Vol-' and insert USB cable
3. Wait until phone enters 'Fastboot' mode
To enable 'Upgrade' mode
1. Power off the phone. Remove SD and SIM cards
2. Press and hold 'Vol-' and 'Vol+' keys and insert USB cable
3. Wait until phone enters 'Upgrade mode'
Found COM ports:
1: COM47 HUAWEI USB COM 1.0
Job ID: 0000000001F6AA99
2024-02-21 12:50:15
Starting Reset Huawei ID
Selected phone model: PPA-LX2
Warning: Please, make sure the phone`s battery is fully charged and connected, after connect the device via Factory Mode (use Hardware Test Point or "ON/OFF Factory Mode option").
Warning: Selected response: Proceed
Searching HUAWEI USB COM 1.0 port...
Detected HUAWEI USB COM 1.0 port
Phone connect successfully
Writing bootloader KIRIN710A_V3...
Initializing remote service connection...
Writing XLOADER partition...
Writing UCE partition...
Writing FASTBOOT partition...
Operation in progress. Please wait for instructions...
Bootloader Update successfully
Rebooting to fastboot mode...
Warning: If you use modified USB cable please reconnect cable from the mother board and press "Ok" to proceed the operation
Warning: Selected response: Ok
Searching Fastboot devices...
Found android device: AKPNU20B05106961
Detected Android Sooner Single ADB Interface port
Reading basic data...
Device Model: DNN-LX9
System: DNN-L29 3.1.1.212(C10E1R3P2)
Android Version: 10
Base Version: DNN-LGRP2-OVS 3.1.1.212
Custom Version: DNN-L29-CUST 10.1.1.1(C10)
Preload Version: DNN-L29-PRELOAD 10.1.1.2(C10R3)
C_Version: C10
D_Version: D000
FB Lock State: LOCKED
User Lock State: LOCKED
Downloading resource...
Connecting to the credit server...
Username: Default_user
Checking balance...
Your balance: 1 credits
Sending device information...
Sending firmware information...
Removing firmware protection...
Connecting to server...
Waiting for a response from the server...
FB Lock State: UNLOCKED
User Lock State: LOCKED
Device Model: DNN-LX9
System: DNN-L29 3.1.1.212(C10E1R3P2)
MEID: 00000000000000
IMEI A:
IMEI B:
S/N: AKPNU20B05106961
Resetting Huawei ID...
Rebooting device...
Warning: Please perform "Clear data" manually via Recovery Mode, if your device doesn`t start properly!
Reset Huawei ID done.
Performed by 1.3.4 Software version.
Welcome to Octoplus Huawei Software v. 1.3.4
To enable 'Manufacture' mode dial
- for Qualcomm and Hisilicon based models: *#*#2846579#*#*
ProjectMenu > Background Settings > USB Port Settings > Manufacture Mode
- for MTK based models: *#*#14789632#*#*
ProjectMenu > Background Settings > USB Port Settings > Debug Mode
To enable 'Fastboot' mode
1. Power off the phone. Remove SD and SIM cards
2. Press 'Vol-' and insert USB cable
3. Wait until phone enters 'Fastboot' mode
To enable 'Upgrade' mode
1. Power off the phone. Remove SD and SIM cards
2. Press and hold 'Vol-' and 'Vol+' keys and insert USB cable
3. Wait until phone enters 'Upgrade mode'
Found COM ports:
1: COM47 HUAWEI USB COM 1.0
Job ID: 00000000018F7735
2024-02-21 12:35:27
Starting Reset FRP
Selected phone model: PPA-LX2
Warning: Please, make sure the phone`s battery is fully charged and connected, after connect the device via Factory Mode (use Hardware Test Point or "ON/OFF Factory Mode option").
Warning: Selected response: Proceed
Searching HUAWEI USB COM 1.0 port...
Detected HUAWEI USB COM 1.0 port
Phone connect successfully
Writing bootloader KIRIN710A_V3...
Initializing remote service connection...
Downloading resource...
Writing XLOADER partition...
Writing UCE partition...
Writing FASTBOOT partition...
Operation in progress. Please wait for instructions...
Bootloader Update successfully
Rebooting to fastboot mode...
Warning: If you use modified USB cable please reconnect cable from the mother board and press "Ok" to proceed the operation
Warning: Selected response: Ok
Searching Fastboot devices...
Found android device: AKPNU20B05106961
Detected Android Sooner Single ADB Interface port
Reading basic data...
Device Model: DNN-LX9
System: DNN-L29 3.1.1.212(C10E1R3P2)
Android Version: 10
Base Version: DNN-LGRP2-OVS 3.1.1.212
Custom Version: DNN-L29-CUST 10.1.1.1(C10)
Preload Version: DNN-L29-PRELOAD 10.1.1.2(C10R3)
C_Version: C10
D_Version: D000
FB Lock State: LOCKED
User Lock State: LOCKED
Downloading resource...
Connecting to the credit server...
Username: Default_user
Checking balance...
Your balance: 1 credits
Sending device information...
Sending firmware information...
Removing firmware protection...
Connecting to server...
Waiting for a response from the server...
FB Lock State: UNLOCKED
User Lock State: LOCKED
Device Model: DNN-LX9
System: DNN-L29 3.1.1.212(C10E1R3P2)
MEID: 00000000000000
IMEI A:
IMEI B:
S/N: AKPNU20B05106961
Resetting FRP...
Writing FRP partition..
Rebooting device...
Reset FRP done.
Performed by 1.3.4 Software version.
Lütfen konu altına yorum yaparken Teşekkürler, Elinize sağlık, süper, sağol, helal olsun gibi kelimeler yazıp konuları kirletmeyelim.
Herkes aradığını bu mesajlar yüzünden bulamıyor.
Altta beğen butonuna basmanız yeterlidir.
Konu ile ilgili sorununuzu veya çözümünüz varsa yorum yapın.
Konu ile alakasız cevaplar silinecektir.
Herkes aradığını bu mesajlar yüzünden bulamıyor.
Altta beğen butonuna basmanız yeterlidir.
Konu ile ilgili sorununuzu veya çözümünüz varsa yorum yapın.
Konu ile alakasız cevaplar silinecektir.